most people take a one piece scope base and have the slot cut into it.
Type: Posts; User: akajun
Forum: Gunsmithing Tips & Tricks
most people take a one piece scope base and have the slot cut into it.
Forum: Leverguns
ill add also slug both ends of the barrel, make sure that the muzzle is smaller than the breach, at least the same size.
Forum: Gunsmithing Tips & Tricks
oh no it affected balance, not that bad though. putting it up front helped control recoil and muzzle flip better than in the butt. glued it right in the hollow of the forend but you could always...
Forum: Gunsmithing Tips & Tricks
I glued one in the forend, way more effective than the butt
I used 2ton epoxy, scuff up the surface of the plastic, wipe with mek, repeat, then put in a little epoxy, put the tube in, then fill with...
Forum: Gunsmithing Tips & Tricks
You can buy an interchangeable counterbore set for not much money, or simply step drill it with progressively larger bits
I’d rather do that than mess with my trimmer
Forum: Special Projects
If you “ open them up” as you say
You will need to make a new piston to fit or you will have lube squeezing out everywhere at .001-.002 thou over
Cheaper to just buy what you need
Forum: Our Town
Controlled burning reduces tick numbers as well. What about the sacks of pesticide powder i see hanging under cattle feeders, in barns, etc? I would think that would be effective as well from a...
Forum: Gunsmithing Tips & Tricks
Yup
Modern high temp bearing grease is best, especially on the line or in the south
When temps rise or the gun warms up, lubriplate and most other grades run and fling
Red high temp bearing...
Forum: Our Town
IIIRC youre in Vicksburg, so those are Miss River Barges. Not often do they take them out of the water for repair, usually most stuff is done in water, unless its really bad like major welding,...
Forum: Gunsmithing Tips & Tricks
for that price you can send it out and have it back bored and extrusion honed and keep most of that money in your pocket.
Forum: Case Forming / Re-forming
Way back when I got in a group buy for a special run of Lee 5.45 dies, I simply formed brass from 556 nato brass. simply trimmed, it about 10-.20 thou long, sized in a 222 die, then anealed it and...
Forum: Gunsmithing Tips & Tricks
Ptg unithroater is what you want
No lathe needed, turns by hand and stays concentric to the existing throat
Most throaters need to be used in a lathe to get good results.
Before you do that...
Forum: Gunsmithing Tips & Tricks
Brownells sells a kit which is a modified brake cylinder hone
Comes with different grit stones .
That’s what I use, but keep in mind, if it’s badly pitted you bay need a backbore reamer to fully...
Forum: Gunsmithing Tips & Tricks
I’d like to see him also test those same barrels with an xrf gun to determine composition
While hardness is important, steel composition is important as well and annealed 4140 can be similar in...
Forum: "The Barrel Works"
Doubt it was a squib or stuck bullet
If I was a handgun maybe , seem plenty of bulged 38’s, 9mm’s etc but even at low handgun velocities the barrel is sufficiently bulged on the outside to be seen...
Forum: Gunsmithing Tips & Tricks
ridgid dark or oaty dark, all I use for stainless and cm barrels.
Forum: "The Barrel Works"
If they’re keyholing with jacketed bullets
Not much you can do other than rebarrel
You can try to counterbore if it’s a muzzle erosion issue but unless you have a lathe, generally not worth it
Forum: "The Barrel Works"
I’m in Brusly / Baton Rouge
When you get your barrels turned down get with me
Forum: "The Barrel Works"
where in LA are you located, if all you need is threading I can help if your not in a rush
Forum: Our Town
get a larger aperture. On all my palma/match rifles I use adjustable iris front and back. As Ive gotten older the rear iris gets bigger, the front stays the same but I put a magnafying lens on it. ...
Forum: Our Town
Heck if you can move quiet in the woods, walk up behind them downwind
You can football punt them or catch ‘em lol
Forum: Our Town
What kinda armadillos do y’all have there? Up armored?
I’ve killed thousands with various pellet guns over the years
22’s too
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |