GCd some 145gr and PCing for BO.
Type: Posts; User: popper
Forum: Our Town
If using google mail, might be them. Or your cookie settings. AVG may be blocking.
Forum: Frequently Asked Questions
WSF works fine in 40sw with 165gr cast. About the same as hp38.
Forum: Cast Boolits
Cast a pot full of 9mm slugs. Shoulder is tired.
Forum: Coatings and Alternatives
Molecules move around in a solid metal, higher temp, more movement. It takes time at temp to get them arraigned right. Temperature of quenching water determines the rate (faster is better) of cooling...
Forum: Factory & Surplus Powder
Drying of nitrocellulose is very dangerous.
Forum: Our Town
Just check used car lots and national sales Co. Her sis got a used toyota with side ramp. He passed earlier this yr and she sold it for about 10k$. They are around.
Forum: Our Town
Had double done a loong time ago, doc told me to quit riding MC for a while. Otherwise, pain recovery but healing was complete. Just move slow and don't over stretch anything.
Forum: Single Shot Guns
Why would anyone getting a Ruger #1 think they were a moron? If only I could afford one.
Forum: Coatings and Alternatives
In several years of shooting pistol/rifle with HiTek/PC/lubed I've not seen enough difference in accuracy that can be attributed to the 'lube'. Powder/alloy/load makes too much difference.
Forum: Coatings and Alternatives
I tried the spraying/baking plates long time ago. I shot AR10 308, several 300BO ARs. NO problem with gas port. Carbon and lead can cause a problem. Mine are adjustable, tweak the screw every once...
Forum: Lead and Lead Alloys
I just put a known alloy bullet in a vice with unknown, squish hard. Look at the dents on both to determine if it's 'good' enough.
Forum: Our Town
Most of eastern side of Ne has been taken over by Mexican/Arab peoples. Expect the rest to go also, just like the smaller Ks towns.
Forum: Our Town
Reminds me of trip to Fl, son wanted to fish off the bridge. Got a blowfish and then an eel. Had to get the side cutters to cut the stainless leader. He wouldn't get near it. Now his company says he...
Forum: Frequently Asked Questions
Grind off 50 thous of the bottom of the die (not shell holder - they are HARD). Screw down the die extra 1/2 turn and size a case. If the bolt closes with little resistance, that's good for YOUR...
Forum: Leverguns
Old or BAD brass! Neck is filthy. IF purchased lately send to Rem, otherwise, just toss the cases. Annealing probably won't fix.
Forum: Shot Loads For Pistols
An old teacher told me the use of the 1911 45 (WWII Pacific) was predominantly to kill Warf rats. They couldn't get tommy guns for dock patrol.
Forum: Boolit Lube !
Nope, not needed. BLL actually degrades PC. Tested on rifle bullets.
Forum: Hunting with CB's
Dang, none for me to shoot. Was watching an (pro) Aussie shoot them @200 yds with sub 308W. Interesting (and he is a good shot) sub 308 220 gr has LESS energy and poorer traj than 300 BO 135gr...
Forum: Lead and Lead Alloys
Trigger, not sure what you are asking. yes sulfur will combine ( form a molecule) with zinc to remove zinc. Yes, remaining sulfur will stay in the lead. I did cast for 40sw, pure & zinc <1%, alloy...
Forum: Lead and Lead Alloys
Solubility of sufur in lead is quite high at higher temps, decreases at lower temps. Correct, it is held in the lead lattice but does NOT form a new molecule. Same with most added elements in lead. ...
Forum: Factory & Surplus Powder
I've used red dot in BO, 30/30 for plinking. Haven't seen the position sensitivity yet. I use a single shot CVA so random 'position' of the rnd when loaded. But BO is a small case. I did notice the...
Forum: Casting Equipment
The NOE has an edge to do the sizing (at least the original), basically a tapered hole. Doesn't work well for me. Using nose sizer in the body, ya can't pull the bullet out easy (and held in with a...
Forum: Frequently Asked Questions
.are undersized boolits that inaccurate? Yup. They get 'damaged' in the bore and don't fly right.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |