Search:

Me thinks...No...It means that you know enough to "Search"
Some sites admonish folks who ressurect old Threads...yet admonish again because you could have Searched!!!
Screwballs do Not believe...

Been Using LINUX for years...Everytime I see crap like this I thank God and Linux, I no longer depend on Windoze, nor Apple!!!!

That is absolutely a Likely Scenario... Why no one else thought of that??? In General, I have certainly had Hard Extraction, (usually, but not always, over pressure), without other cylinder...

@Cast10... Nice Blammer
Or, Was the 351 the Blammer???

But...In the Old Days...Unique was very specializes also...Wonderment is...What off the Wall Uses is WSF???
or...What makes Unique...Truly Unique!!!! use in 25ACP to 30-06!!!

In This....I believe!!!

Someone right here has a good compilation..Let me find it..

good a place to start as any..
https://castboolits.gunloads.com/showthread.php?14300-Updated-List-of-Lee-Moulds

2 powders instead of one.. if I get where I cannot get Unique, nor BE-86...I may look to WSF...Maybe...Someone try it out OK??

Perhaps it is Power Pistol that BE-86 actually Is, except with flash suppressant.
https://castboolits.gunloads.com/showthread.php?381469-BE86-vs-Power-Pistol-blast

Very interesting indeed.. so just empty brass makes a difference?? I have Never tested that but...seems strange indeed...

Darn good Question.. I discovered that BE-86 is some other powder, except with flash retardant...they say...All I know is, all I have put it in, have been Grain for Grain (Not Volume), weight,,, it...

Load er up like it is Unique...You gonna Like It!!

I'm sticking with Boolit seated too deep on this one!!!

Every single one..handgun too!!!
First thing is you will find that Grain for Grain seems a Good starting point...actually mostly I just stay there..a bit softer but...IDC
The Smaller Calibers...ie...

If it was seated much deeper....it certainly would cause over pressure.. Seating Depth is Very Important...

Except Remington 6-1/2's...they are fragile cups truly..I'm warnin ya!!!Stay at lower Pressures with them...like Remington Advises!!!

Indeed...just a good load.. 14.0 gr is 1130 to 1150 fps in my 4" DW..
I do Not have any problem using SRP or SPP. interchangeably...tho I generally use SRP, in place of SPMag primers...and Not Rem...

I still get along well with my Old Lyman hand tools.. Admittedly I do Not fool with many crimped primers!! Uniforming, yes, I have done it!

Plus one for "change guns", The open sighted 22LR barrel for my Contender Never...Ever, misses, with a small stash of very old Remingtons I keep aside. When me or the Wife develop a Problem...out...

Been scoping Contenders since the late '70's early '80's...Maybe I should try a "dot".... For some reason, I still feel Comfortable with a Really Good set of open sights!!!

Here is a link to wiki good as any
https://en.wikipedia.org/wiki/Babbitt_(alloy)

Aint that the truth!!!!

I have never used any but Green Dot... serves very well indeed. I avoid other uses so I will have Green Dot for my 20ga!!!!

At one time I had a Babbitt alloy Chart...there are many it turns out..
I will try to find it! Lots of stuff besides lead, tin, and antimony, in Babbitt...I remember that!!!

Problem...700x cost is considerably higher than Nitro100NF, yet N100NF is entirely acceptable on clean. Yet costs less! And, N100NF is Very bulky, not like Trail Boss, but less is required than Trail...